delta 6 jointer manual

25x25mm Hex Socket Head Screw (2) 24. NOTE: A spring is supplied in knob assembly (E) that returns the guard (C) over the cutterhead after a cut has been made. To adjust the stops, loosen two locknuts (F) and (G) Fig. Then adjust the height of the knife by turning the knife raising screws (F) Fig. The ”gib” for the infeed table is shown at (A) Fig. 46, and the “gib” for the outfeed table is shown at (B) Fig. To raise the knife, use wrench (E) Fig. 58, and turn raising screw clockwise until the knife just touches the straight edge (J) on each end and center of the cutterhead when the knife is at its highest point. For surfacing, the major flat surface of the workpiece is placed on the infeed table of the jointer with the narrow edge of the workpiece against the fence, as shown in Fig. Delta will repair or replace, at its expense and at its option, any Delta machine, machine part, or machine accessory which in normal use has proven to be defective in workmanship or material, provided that the customer returns the product prepaid to a Delta factory service center or authorized service station with proof of purchase of the product within two years and provides Delta with reasonable opportunity to verify the alleged defect by inspection. Learn more - opens in a new window or tab This amount is subject to change until you make payment. For additional information, see the Global Shipping Programme terms and conditions - opens in a new window or tab This amount is subject to change until you make payment. If you reside in an EU member state besides UK, import VAT on this purchase is not recoverable. For additional information, see the Global Shipping Programme terms and conditions - opens in a new window or tab Delivery times may vary, especially during peak periods and will depend on when your payment clears - opens in a new window or tab.

• delta 6 jointer manual, delta 6 professional jointer manual, delta 6 jointer 37-280 manual, delta 6 variable speed bench jointer manual, delta 6 jointer manual, delta 6 jointer manual, delta 6 jointer manual, delta shopmaster 6 jointer manual, delta 6 professional jointer manual, 6 inch delta jointer planer manual.

If an extension cord is used, use only 3-wire extension cords which have 3- prong grounding type plugs and 3-hole receptacles which accept the tool’s plug. Unit includes; 10 amp, 120 volt motor with variable speed range from 6000 to 11,000 rpm and cutting speed range from 12,000 to 22,000 cpm, dust chute, center-mounted fence, two-knife cutterhead, cutterhead guard and lock, wrenches and push blocks. The workpiece is positioned on the jointer with the narrow edge of the workpiece on the infeed table and the major flat surface of the workpiece against the fence, as shown in Fig. DO NOT COMPLETELY TIGHTEN SCREWS (A) AT THIS TIME. 2. Assemble guard mounting bracket (B) Fig. 14, to the two screws (A) as shown, and tighten the two screws (A). Speed indicators of 1-2-3-4 and 5 are provided on the speed dial as shown. To check and adjust the positive stops, proceed as follows: 4. Place a square (C) Fig. 26, on the table with one end of the square against the fence as shown. Loosen one half turn or only enough so knife can slide between locking plate and cutterhead. The wood should rest firmly on both tables as shown in Fig. The following directions will give the beginner a start on jointer operations. Use scrap pieces of lumber to check the settings and to get the feel of the operations before attempting regular work. Avoid forcing such material down against the table; excessive pressure will spring it while passing the knives, and it will spring back and remain curved after the cut is completed. If you do not have access to any of these, call 888-848-5175 and you will be directed to the nearest Porter-Cable Delta Factory Service Center. If an extension cord is used, use only 3-wire extension cords which have 3- prong grounding type plugs and matching receptacle which will accept the machine’s plug. Dust Chute 18. V-Belt 19. Pulley 20. M10x1.5x20mm Hex Socket Head Screw (3) 21. M8x1.25x55mm Hex Socket Head Screw (4) 22. M8x1.25x30mm Hex Socket Head Screw (2) 23. M8x1.

In order to navigate out of this carousel please use your heading shortcut key to navigate to the next or previous heading. Register a free business account To calculate the overall star rating and percentage breakdown by star, we don’t use a simple average. It also analyzes reviews to verify trustworthiness. Please try again later. Normand 5.0 out of 5 stars. In 1923 he started manufacturing a small scrollsaw based on a design licensed from its inventor, Carl Moberg. Beginning in 1929, Tautz started identifying Delta Specialty Co.The Delta name was difficult to trademark in other jurisdictions so the Tauco name was used instead. We are uncertain of the ownership of Tauco and it is possible that it existed before the 1939 Marshall Field buyout. About the same time Rockwell also purchased Crescent Machine Co. Delta Manufacturing became Rockwell's Delta Power Tool Division. Shortly thereafter, Delta tools were labeled Delta Rockwell. It appears that the saws and their motors were manufactured for Rockwell by A. O. Smith Corp., which had already been making motors for Rockwell, and possibly for Delta before the purchase by Rockwell. The former Callander Foundry continued to operated as Rockwell International of Canada, Ltd. In 1981, the line of handheld power tools was sold to Pentair Inc. of St. Paul, MN, which operated it as the Porter-Cable line—a name that had disappeared shortly after Rockwell bought the Porter-Cable Machine Co. Pentair operated it as the Delta International Machinery Corp., which included the Canadian operations. Also beginning in the early 1990s, Lindquist Machine corp.In 1995, Delta bought rip-fence maker Biesemeyer Manufacturing Corp. In the late 1990s, Pentair merged Delta's and Porter-Cable's manufacturing operations in Jackson, Tennessee. In 2000, the two divisions were formally merged. The new company is Delta Power Equipment Corp.

Learn More - opens in a new window or tab Learn More - opens in a new window or tab Learn More - opens in a new window or tab Learn More - opens in a new window or tab Learn More - opens in a new window or tab See the seller's listing for full details. Contact the seller - opens in a new window or tab and request a postage method to your location. Please enter a valid postcode. Please enter a number less than or equal to 45. Sellers may be required to accept returns for items that are not as described. Learn more about your rights as a buyer. - opens in a new window or tab You're covered by the eBay Money Back Guarantee if you receive an item that is not as described in the listing. Please let us know if you have any questions or if you couldn't find a manual you were looking for.All Rights Reserved. User Agreement, Privacy, Cookies and AdChoice Norton Secured - powered by Verisign. Please choose a different delivery location.Our payment security system encrypts your information during transmission. We don’t share your credit card details with third-party sellers, and we don’t sell your information to others. Please try again.Please try again.Please try again. This is NOT an original as originals are out of print, but we use the best scans available. Plastic Comb Bound with clear plastic on front and back covers to help protect manual. All manuals are in public domain or printed with permission. Then you can start reading Kindle books on your smartphone, tablet, or computer - no Kindle device required. Register a free business account To calculate the overall star rating and percentage breakdown by star, we don’t use a simple average. Instead, our system considers things like how recent a review is and if the reviewer bought the item on Amazon. It also analyzes reviews to verify trustworthiness. All manuals are in public domain or printed with permission. Then you can start reading Kindle books on your smartphone, tablet, or computer - no Kindle device required.

Make sure your extension cord is in good condition and is a 3-wire. Pagina 6 DEFINITIONS OFPagina 10 ASSEMBLINGIf during operation, there is any tendency for the jointerYour jointer is supplied with a variable speed controlPagina 13 3. The fence features adjustable positive stops at thePagina 16 PUSH BLOCKS. A set of push blocks (A) Fig. 37, is supplied with yourPagina 17 PLANING WARPED PIECES. If the wood to be planed is dished or warped, take light cuts until the surface. Pagina 18 MAINTENANCEPagina 20 NOTES. You should update your web browser to a more recent version.Attempting to reconnect to the server. Try reloading this page. You you will need to refresh the page to see those changes! This affiliate accepts Cash, Visa, MasterCard, Discover, NO CHECKS.Everything is sold “as is, where is” with no guarantees or warranties. You are responsible for inspecting items prior to purchase. There is a 13% BUYERS PREMIUM (13% BP) on this auction. Applicable Minnesota Sales Tax will be collected. At the close of the auction active items will remain open until no bids have been received for three minutes. IMPORTANT NOTE: If the high bidder of an item does NOT acknowledge the purchase, K-BID systems reserves the right to determine how and to whom it will be resold. If we determine that the winning bid was not a bona fide bidder, the item WILL NOT AUTOMATICALLY go to the next second-highest bid. Once a bid is placed, you are obligated to purchase if you are the winning bidder. Failure to purchase for any reason will result in your bidder number being disabled and pending bids cancelled. Our fraud control system will NOT allow you to bid by creating another user account. By placing a bid on this auction, you are agreeing to the auction specific terms listed on this page in additions to the K-BID user terms and agreements. Affiliates are not employees, agents, representatives or partners of K-BID Online, Inc.

The CEO has said that the Delta products currently manufactured in the United States will continue to be made there. Keith's history article also provides information on specific product: when they were introduced, and how they changed over the years. Paint colors, how to rebuild a scrollsaw air pump, a type study of Delta cast-iron stands, information specific to bandsaw, lathes, Unisaws, and more. Check the Delta website first; some manuals are available there for free download. Be sure to have either a model number or serial number handy. There is a small fee for manuals sent by mail. Well, there isn't much information past the mid-1980s but Delta can provide information on those more recent machines. Some of these facts are in dispute. This assertion is contradicted by the evidence above. Please contact us if you can provide more solid evidence one way or the other. VintageMachinery.org does not provide support or parts for any machinesPlease remember that safety standards haveIt is up to the individual user to useThe VintageMachinery.org. They are small, strong, simple tools that can chip off the excess of a joint that. I found the newer models thatg have allen set screws to adjust the blades, but this looks like it has nuts holding the. Per the owners manual it says it can run on 110 or 220 Help Please !!! Often, the 220 wiring diagram is on the back side of the plate that's screwed on the. We are suppose to be able to get print it on. Could you please help me exactly where to get this information.. Go to eReplacementParts.com: Power Tool Parts and Tool Repair. If you need more. Answer questions, earn points and help others. Woodworking can be dangerous if safe and proper operating procedures are not followed. As with all machinery. Pagina 3 ADDITIONAL SAFETY RULES FOR JOINTERSNEVER make jointing. Pagina 4 CONNECTING TOOL TO POWER SOURCEThis circuit. Pagina 5 EXTENSION CORDS. Use proper extension cords.

We make some ofThe duck call pictured has over 1,117 individual pieces of wood in it. You can learn more about our shop on our About Us page, or Ozarkwoodworker.com. That is why we started Ozark Shop Talk Blog to give back to the many people that have helped us learn. We are self-taught machinist and woodworkers, and we had to use the How-To Books, and information in the manuals to learn ourselves. Something went wrong. View cart for details. This is the price (excluding shipping and handling fees) a seller has provided at which the same item, or one that is nearly identical to it, is being offered for sale, or has been offered for sale in the recent past. The price may be the seller's own price elsewhere, or another seller's price.User Agreement, Privacy, Cookies and AdChoice Norton Secured - powered by Verisign. If your machine is not listed here, there is a good chance you can still find the knives you are looking for based on dimensions. Please measure your old knives (LENGTH x WIDTH x THICKNESS) and search for these knives in our sections: Hardness: 62-63 Hrc Rock. Hardness: 62-63 Hrc Rock. Hardness: 62-63 Hrc Rock. Hardness: 62-63 Hrc Rock. Hardness: 62-63 Hrc Rock. Hardness: 62-63 Hrc Rock. Hardness: 62-63 Hrc Rock. Hardness: 62-63 Hrc Rock. Hardness: 62-63 Hrc Rock. Hardness: 62-63 Hrc Rock. Hardness: 62-63 Hrc Rock. Hardness: 62-63 Hrc Rock. Hardness: 62-63 Hrc Rock. Hardness: 62-63 Hrc Rock. Hardness: 62-63 Hrc Rock. Hardness: 62-63 Hrc Rock. Hardness: 62-63 Hrc Rock. Hardness: 62-63 Hrc Rock. Hardness: 62-63 Hrc Rock. Hardness: 62-63 Hrc Rock. For additional information, see the Global Shipping Programme terms and conditions - opens in a new window or tab Delivery times may vary, especially during peak periods.

Learn More - opens in a new window or tab Learn More - opens in a new window or tab Learn More - opens in a new window or tab Learn More - opens in a new window or tab Learn More - opens in a new window or tab Learn more The item may be missing its original packaging, or the original packaging has been opened or is no longer sealed. The item may be a factory second, or a new and unused item with minor defects. See the seller’s listing for full details and description of any imperfections. Contact the seller - opens in a new window or tab and request a postage method to your location. Please enter a valid postcode. Please enter a number less than or equal to 5. All Rights Reserved. Page 2 SAFETY RULES Woodworking can be dangerous if safe and proper operating procedures are not followed. As with all machinery, there are certain hazards involved with the operation of the product. Using the machine with respect and caution will considerably lessen the possibility of personal injury. However, if normal safety precautions are overlooked or ignored, personal injury to the operator may result. If an extension cord is used, use only 3-wire extension cords which have 3prong grounding type plugs and 3-hole receptacles which accept the tool’s plug. Page 5 EXTENSION CORDS Use proper extension cords. Make sure your extension cord is in good condition and is a 3-wire extension cord which has a 3-prong grounding type plug and a 3-hole receptacle which will accept the tool’s plug. When using an extension cord, be sure to use one heavy enough to carry the current of the tool. An undersized cord will cause a drop in line voltage, resulting in loss of power and overheating. Fig. DD, shows the correct gauge to use depending on the cord length. The workpiece is positioned on the jointer with the narrow edge of the workpiece on the infeed table and the major flat surface of the workpiece against the fence, as shown in Fig. 2.

K-BID’s knowledge about individual auctions and individual auction transactions is limited to the information appearing on the website. Bidders are responsible for bids placed on their account. Removal day is not inspection day. When an auction ends, and the winning bidder invoice appears on the bidder’s dashboard, the bidder is obligated to honor their bid(s). You are responsible for inspecting items prior to purchase. Once a bid is placed it cannot be retracted. Duplicate bidder accounts will be deactivated when they are determined to exist. If possible and at our discretion, K-BID reserves the right to delete any bid we believe has been placed by a suspect bidder. Any registration that shows up on our fraud detection system may be placed on hold and bids removed until the user is verified. K-BID Online, Inc reserves the right to disallow anybody from bidding on its website. Cases of obvious bidding with no intent to redeem will be referred to appropriate legal authorities. If the reserve is lowered while the auction is in progress, the applicable reserve message will appear below the Next Required Bid information (Reserve Not Met or Reserve Has Been Met); the asset will sell to the high bidder if the lowered reserve amount is met. If the reserve is lowered after the auction closes, the highest bidder at auction close will receive a winning bidder invoice. Delta Machinery strongly recommends that this. Delta Jointer Owner's Manuals are free to download.View online or download Delta JT160 Instruction Manual View and Download Delta JT160 instruction manual online. 6'' Variable Speed Bench Jointer. Power tool manuals and free pdf instructions. Find the user manual you need for your tools and more at ManualsOnline. World's leading marketplace. Operating Instructions and Parts Manual 8-inch Jointer-Planer Model JJP-8BT JET 427 New Sanford Road LaVergne, Tennessee 37086 Part No. This symbol is used to alert the user to useful. Thank you for choosing DELTA’ s PLC DVP.

Go to Dewaltservicenet.com and in the middle of the page towards the bottom type in your model number. Manuals and free owners instruction pdf guides. Find the user manual and the help you need for the products you own at ManualsOnline. AMT Jointer Model 4800 owners manual. It is up to the individual user to use good judgment and to safely operate old machinery. The VintageMachinery.org. Find Product Manuals. Misplaced your user manual?. Delta Owner's Manuals. CONTINUE. Quickly download owner manuals for thousands of products. Delta products sorted by category. Browse and choose what you need. Dewalt Dw682k Biscuit Joiner Manual The DeWalt DW682K Plate Joiner allows the user to make extremely As with all power tools, users should read the manual before. Crescent, Delta, Northfield,.Delta 37-070 Biscuit Joiner User Manual. Delta 37-070 Manual is an interesting program that can display and play a ridiculous number of different file types. Im looking at a older used Rockwell Jointer. The Following User Says Thank You to JohnK007 For This Useful Post: Lawdog (01-30-2011) Craftsman Wood Planer Manual Sears 113.206931 User's Manual. When creating rabbets in incremental passes as directed in the instructions in the manual the. Need to fix your 37-190 Type 1 Jointer. We have parts, diagrams, accessories and repair advice to make your tool repairs easy. Delta Rockwell Homecraft Radial. It is up to the individual user to use good judgment and to safely. Reload to refresh your session. Reload to refresh your session. As a self-taught craftsman, I’ve frequently needed manuals and books to help myself set up or operate complicated machines. That is why I started this service with my family- to make hard-to-find manuals easier for other craftsmen to obtain. I wanted to make the best quality, printed manuals to work with in a shop. After all, I remember the day when they didn’t even have computers.

The workpiece is moved from the infeed table, across the cutterhead to the outfeed table. 2. Page 7 11 13 6 4 5 1 8 10 16 7 14 15 9 3 12 2 Fig. Page 8 ASSEMBLY INSTRUCTIONS WARNING: FOR YOUR OWN SAFETY, DO NOT CONNECT THE TOOL TO THE POWER SOURCE UNTIL THE MACHINE IS COMPLETELY ASSEMBLED AND YOU HAVE READ AND UNDERSTAND THE ENTIRE OWNERS MANUAL.Page 12 VARIABLE SPEED CONTROL Your jointer is supplied with a variable speed control knob (A) Fig. 23, that enables you to operate the machine at cutterhead speeds between 6000 and 11,000 RPM. Speed indicators of 1-2-3-4 and 5 are provided on the speed dial as shown. A C B SPEED CONTROL CHART A speed control chart (C) Fig. Page 13 3. The fence features adjustable positive stops at the most used fence positions of 90 degrees and 45 degrees to the right. To check and adjust the positive stops, proceed as follows: 4. Place a square (C) Fig. 26, on the table with one end of the square against the fence as shown. Adjust the fence until it is exactly 90 degrees to the table. C Fig. 26 5. Turn set screw (D) Fig. 27, until it contacts stop (E). D E Fig. 27 6. Using a square (C) Fig. Page 14 ADJUSTING KNIVES When it becomes necessary to adjust the knives due to replacement or wear, proceed as follows: D F A E B C Fig. 31 Fig. 30 1. DISCONNECT THE TOOL FROM THE POWER SOURCE AND REMOVE CUTTERHEAD GUARD. 2. Rotate cutterhead and loosen four screws (A) Fig. 30. NOTE: Do not overly loosen the screws (A). Loosen one half turn or only enough so knife can slide between locking plate and cutterhead. 3. Rotate cutterhead and engage cutterhead lock (B) Fig. 31, on cutterhead shaft as shown. Page 15 8. If the knives are set too high, the work will be gouged at the end of the cut, as shown in Fig. 33. MATERIAL IN-FEED TABLE OUT-FEED TABLE KNIVES SET TOO HIGH CUTTER GOUGE Fig. 33 9. As a final check, run a piece of work slowly over the knives for 6 to 8 inches. The wood should rest firmly on both tables as shown in Fig.

34, with no open spaces under the finished cut. MATERIAL OUT-FEED TABLE KNIVES AT CORRECT HEIGHT IN-FEED TABLE CUTTER Fig. Page 16 PUSH BLOCKS A set of push blocks (A) Fig. 37, is supplied with your jointer and should be used whenever possible to minimize all danger to your hands. Fig. 37, illustrates using the push blocks properly. A Fig. 37 OPERATION The following directions will give the beginner a start on jointer operations. Use scrap pieces of lumber to check the settings and to get the feel of the operations before attempting regular work.Avoid forcing such material down against the table; excessive pressure will spring it while passing the knives, and it will spring back and remain curved after the cut is completed. Please visit our Web Site www.deltamachinery.com for a catalog or for the name of your nearest supplier. WARNING: Since accessories, other than those offered by Delta, have not been tested with this product, use of such accessories could be hazardous. For safest operation, only Delta recommended accessories should be used with this product. I believe the download here is faster, and there are no ads at all. Nevertheless, I like this one more than others. Services: Sync music, Manage music, Recover missing metadata, Record CDs Download MediaMonkey Now Buy MediaMonkey Gold Get Addons Never use any other conversion tool again. Find Music File Converter Mp3 Mp3 converter www.easypdfcombine.com Merge And Convert Files Into PDFs For Free With EasyPDFCombine App. Our Planer and Jointer knives are designed to provide extended life between sharpenings and are made with quality as our first priority. Each one is forged from a premium grade of European D2 High Speed Tool Steel which is produced in the famed Bohler Steel Mill in Austria. We specify a Rockwell hardness of 60 HRC to maximize abrasion resistence, increase the steel's ability to hold a cutting edge, and improve its resistance to deformation at elevated temperatures.

But using ultra-premium material is just the beginning. The production process we use sets us apart. This exclusive process is more costly than inferior methods but it optimizes stress reduction and increases the longevity of each knife we produce. Finally, we precision grind each knife to a razor finish to ensure you get a perfect cut. Oldsmar, FL 34677. You can use a multimeter to test tool and appliance cords and switches, the two parts usually responsible for electri. It also describes information tools available at eReplacementParts.com. And the company was sold a while ago, so you might be seeing a few more of the parts for their machinery being discontinued. You might try to keep searching on line for the 1340166 lock lever. There were a lot of these jointers sold, so I would hope someone might still have this part for you. Good luck, -WJA Delta makes a knife setting tool part number 37-157 which makes it very simple to do. You loosen the knife screws on the cutter-head, remove the old knife, insert the new knife in the cutter-head, place the setting tool on the outfeed table and over the cutter-head with the new knife in it, tighten up the cutter-head screws and your done. The setting tool uses magnets to hold onto the table and bring the knives up to the correct height. Does anyone know where or how I can download aManual for this planer. 6 replies so far Kinda tough finding somethingbepapa, maybe it's a Delta Rockwell. Rockwell Delta 6 X 48 Belt Sander Model 31-520 Lower Base Parts.49.99 Delta 6 Belt 12 Disc Sander Operator Parts Manual 0208. 17.50.View Details. Delta Rockwell Milwaukee Jointer Sander Band TableSaw Belt Pulley Guard Cover. Item, Photo (Off),Description, Bids, High Bidder, Current How to Delta jointer planermanual Plans PDF toy box seat plans Here is a vintage Delta Rockwellsise long plane Planer Cutter steel meeting place with itm DELTA 6Variable Speed workbench jointer plane 37 070 Delta jointer planer.

15 DELTA ROCKWELL 15 665 BENCH TABLE MOUNT 6 SPEEDDRILL PRESS BALDOR 3PH 1140 Rockwell Delta 37 290 4 In DeluxeJointer Manual 1984 Rockwell Delta 37-290 4 In. Festool product in any way other than in themanner described in the Festool Instruction Manual. Recommended SY17 FactoryTalk AssetCentre - with FactoryTalk View SE. Rockwell Automation Rockwell Automation Rockwell Automation Documents 6 in. Please upgrade your browser to improve your experience. Was wanting some advise on Jointing the knives, the manual had basic info.Using a stone with the jointer running makes me think of bad things happening. Cant wait till I get it up in good working order, I think its a decent jointer Thanks Ron I send my blades out to get sharpened. I am going to buy a second set so I don't have down time. Get a spare set of knives and learn how to change them efficiently. Then take two boards the length of the jointer bed and joint them and put them edge to edge. If they match pefectly, you're golden. If not, then the work begins. The work of figuring out if your technique is off, setting of the knives is off or your tables need attention or all three. These are usually the ones that run 5,000 feet or more of a single run. If you can set your knives to within a thousandth or so it won't be a problem. Even if one knife is higher it will soon be level with the other knives.They've done this a lot for me with my vintage machines aquisitions. I would like to see some picks of your tools. I have 2 old power tools 24 in.Delta scroll saw, Boise Crane lathe. Like you I didn't feel comfortable sharpening the knives in the method that was explained to me but regardless I tried it. I set all the blades with the knife guage then I let the outfeed table down just ever so slightly so the highest portion of the blades just start to touch the stone then very slowly let the out feed table down. When all the blades touch the stone evenly your done.

The biggest problem I have with this method is the blades end up being somwhat rounded over becouse the drum where the blades attatch is round so the blades actually have a rounded edge to them. Of course I didn't have a lot to loose and it couldnt hurt them a lot more than they already were since I had hit a nail with the knives. I do have to admit that this method did work good for straightening the knives. I just ordered a new set of knives from Grizzly since thats the type of my jointer. I figure that I wont have any down time and I'll have this set resharpened. See the results and get an inside view of the process. Sign Up Now. Based on the radius, a new location list is generated for you to choose from. No guard included but one can be made to attach. Upgrading in size so we have no more use.Runs perfect. Inherited it but I already have one. If ad is up, it’s available.Comes with stand, 2 push pads and is very heavy. OBONo guard included but one can be made to attach. Upgrading in size so we have no more use for this one. Willing to deliver locally or further for additional costGone over has upgraded 1 hp Lesson motor 3450 rpm.In very nice shape made in Canada.This is part of a professional woodworking shop being sold off. This is a well cared for machine. Estimating the age to be manufactured circa 1995. But this is not fact, this is an estimate. You have to be capable of moving it from the woodworking shop - 150 feet from the house - to your vehicle. We can do this contactless. Happy to answer further questions.Jointer only. No motor is not included Knives are in good conditionALSO available separately.router table with installed router,.plate jointer If you see it it's available. Only REASONABLE offers will be replied to.Also a broken large if anyone had the knowledge to fix it. (Needs a threaded rod replaced) 700 as full lot, willing to throw I a few extra things if you take.It is a pack of 3 blades.